Pool models, construction conditions and care to help you plan your project.
In this guide 4
Selection note: The Fiplus shell is a 20 mm F-Stone fiber cement panel; the galvanized steel external cross-brace leg is a component separate from the shell. Maldiv and Bora have special alloy steel casings; the casing is not stainless, inox or fiberglass. Shell warranty periods are 25 years for Fiplus and 10 years for Maldiv/Bora; coverage and exclusions depend on the conditions set out in the written warranty document. Size, performance and certification compliance must be verified separately for the selected product and project.
For villa owners who want soft, organic lines in their garden instead of sharp corners, oval forms are an aesthetic solution; building curved formwork in reinforced concrete and laying finishes along oval lines is difficult in terms of labor and generally raises the cost. The Maldiv Oval Prefabricated Pool model from Sermed Havuz combines the oval form with prefabricated production through curved modules bent from a special alloy steel frame at the Düzce factory and side buttresses that resist ground thrust. The Maldiv series, starting at 3x5 meters and extending up to 5x10 meters, is offered with a 10-year casing warranty subject to written conditions.
In the oval form there is no corner obstacle in the path of the water flow; the clean water leaving the nozzles tends to circulate in a circular pattern within the pool, and this helps reduce the formation of deposits in corners. Hydraulic smoothness can contribute to filtration efficiency; however, since we do not have measured data for the energy saving that would be achieved, no proportional saving claim is made.
01. The Hydraulic and Structural Advantages of Oval Forms: Reducing Dead Corners
In rectangular pools, the corners are the regions where circulation remains weak; leaves and sediment tend to collect there. In the Maldiv oval model, by contrast:
- Continuous Circular Hydraulic Circulation: The curved end sections make it easier for the water to be directed along the wall; when the placement of the floor and side nozzles is correctly planned, dirt is carried more effectively toward the skimmer basket.
- Arch Behavior of the Curved Ends: The arc-shaped steel end sections show an arch-like load-carrying behavior against ground thrust from outside and water load from inside, through the effect of hoop stress.
- Side Buttress Support on the Straight Edges: The hydrostatic load arising on the two long straight edges of the oval form is transferred to the ground by triangular steel buttresses anchored into the base concrete. This solution markedly reduces the risk of bulging in the side wall; it cannot be claimed that the risk is entirely eliminated, and the buttress spacing must be verified by structural calculation.
- Integration into Garden Landscaping: Curved lines help the pool take on a more organic, pond-like appearance in gardens with natural stone and dense planting.
02. Maldiv Special Alloy Steel Casing, Side Buttress Engineering and 10-Year Warranty
The heart of the Maldiv pool system is the special alloy steel frame formed at our factory in Düzce Cumayeri:
- Special Alloy Steel Shell: Unlike standard galvanized sheets, steel plates with a protective alloy coating are used. A 10-year warranty subject to written conditions is issued for the casing; the coating class and its technical data should be confirmed from the product documentation.
- Anchoring of the Side Buttresses into the Base Concrete: While the base concrete is being poured, the load-bearing steel profiles of the Maldiv model are anchored so that they act together with the slab. The manufacturer's reference detail is a slab containing 20 cm C30 concrete and Q131 mesh; this reference detail must be adapted according to the geotechnical investigation and the structural calculation. When the pool is filled, the weight of the water contributes to the system bedding onto the ground; on the other hand, the risk of uplift (flotation) must be assessed separately.
- Factory-Made Liner: The single-piece liner, prepared at the factory according to the developed shape of the oval form, is seated into the pool basin by vacuum. Depending on the project, the liner is selected as a 0.8 mm homogeneous or a 1.5 mm reinforced membrane; the two types are not used together in the same product. With correct measurement and installation, wrinkling on the floor and the curves is kept to a minimum.
- Compact Excavation Advantage: Because of the curved end sections, no extra excavation is needed at the corners; compared with a rectangular pool of the same external dimensions, the excavation volume is geometrically smaller. The exact difference varies according to the pool size, the slope and the working allowance, which is why no fixed percentage is given.
03. Maldiv Oval Pool Sizes, Water Volume and Strength Table
The volumes below are approximate calculations made on the assumption of a net water depth of 1.40 m and a stadium geometry with semicircular ends at both ends. The buttress numbers are a typical layout example and the final number is determined according to the structural design.
| Model and Net Size | Water Depth | Approximate Water Volume | Number of Side Buttresses | Ideal Area of Use |
|---|---|---|---|---|
| Maldiv 3.00 x 5.00 m | 1.50 m (Net 1.40 m) | ~18 m³ | Typically 2 units (1 on each side) | Compact detached gardens and terraced villas |
| Maldiv 3.50 x 6.50 m | 1.50 m (Net 1.40 m) | ~28 m³ | Typically 4 units (2 on each side) | Standard family villas and holiday homes |
| Maldiv 4.00 x 8.00 m | 1.50 m (Net 1.40 m) | ~40 m³ | Typically 6 units (3 on each side) | Luxury villas with large gardens and rental properties |
| Maldiv 5.00 x 10.00 m | 1.50 m (Net 1.40 m) | ~62 m³ | Typically 8 units (4 on each side) | Boutique hotels and large land projects |
Conclusion: The Maldiv oval pool combines aesthetic curves with the strength of a steel frame. With correct structural design and installation, the arch behavior of the curved ends and the triangular buttresses serve to help the pool keep its form over a long period.
Frequently asked questions
How are the side support buttresses of Maldiv oval pools fixed against ground thrust, and how much space do they take up?
The steel buttresses on the straight side walls typically extend 80-90 cm outward from the pool frame and are bolted to steel base profiles anchored into the base concrete. Once covered over with gravel and terrace concrete, the buttresses remain out of sight. Buttress length, spacing and anchoring detail are finalized in the structural design according to the pool depth, the ground class and the ground water level, if any.
How is a ladder installed on the curved sections?
In the Maldiv model, stainless steel (for example AISI 316 grade) tubular ladders can be mounted on the straight side walls of the pool or at the start of the curves. Alternatively, curved polyester or liner-covered step groups integrated into the pool can be applied. The ladder type and the anchoring points must be selected to suit the panel/frame detail.
Can a Maldiv pool be installed above ground?
Since the side buttress system of the Maldiv pool is designed to be buried in the ground, a fully recessed installation, or a semi-recessed installation buried at least approximately 1 meter, is recommended. Where an above-ground installation is needed, the circular Bora model is more suitable. On sites with a high ground water table, liner lifting may be seen when the external water load exceeds the internal water load, even if the pool is full of water; for this reason, drainage and, if necessary, a well solution must be defined in the project.
How is the cover for an oval pool produced?
Solar bubble thermal covers and winter safety covers, cut to the curve according to the net dimensions of the Maldiv pool, are produced at our factory and dispatched to site. Covers help reduce heat loss and soiling; however, no cover takes the place of a physical barrier and adult supervision, and none eliminates the risk of drowning.

Fiplus ↗
Maldiv ↗
Bora ↗
