← BlogModels & technology

Bora Round Pool: Rapid Installation and Hydraulic Circulation in Ø2.5-Ø10 m Sizes

In the Bora pool, the supply nozzle is positioned at a tangential angle. The water discharged from the nozzle moves along the circular wall and creates a rotating flow within the pool; in a corner-free structure, this flow makes it easier for the water to be directed toward the skimmer and the floor drain. The circulation time and the filter capacity must be selected according to the pool volume.

7 min
Bora Round Pool: Rapid Installation and Hydraulic Circulation in Ø2.5-Ø10 m Sizes
Sermed Havuz photo · illustrative
Sermed Havuz technical team

Pool models, construction conditions and care to help you plan your project.

In this guide 4
  1. 01The Strength of Circular Geometry: A Buttress-Free Arrangement and Balanced Pressure Distribution
  2. 02Bora Pool Installation Discipline and Vortex Hydraulics
  3. 03Bora Round Pool Diameter, Volume and Installation Types Table
  4. 04Frequently Asked Questions

Selection note: The Fiplus shell is a 20 mm F-Stone fiber cement panel; the galvanized steel external cross-brace leg is a component separate from the shell. Maldiv and Bora have special alloy steel casings; the casing is not stainless, inox or fiberglass. Shell warranty periods are 25 years for Fiplus and 10 years for Maldiv/Bora; coverage and exclusions depend on the conditions set out in the written warranty document. Size, performance and certification compliance must be verified separately for the selected product and project.

For owners of detached villas and for glamping operators who do not want weeks of construction traffic, concrete mixers and extensive excavation in their garden, circular pools are a practical solution. The circular geometry distributes the hydrostatic load evenly along the perimeter; as a result, the need for side buttresses or a retaining wall is removed in most installations. The Bora Round Steel Casing Pool, manufactured at Sermed Havuz's Düzce factory, is offered with a size range extending from Ø2.5 meters to Ø10 meters in diameter, an installation capability that can be completed in a single day at small diameters, and a 10-year casing warranty subject to written conditions.

Rapid installation stems from moving a significant part of the site labor to the factory. On small-diameter Bora pools, installation can be completed within the same day under suitable site conditions; on the other hand, the duration depends on ground preparation, access, weather conditions and the electrical/pipework infrastructure, and no fixed duration is guaranteed.

01. The Strength of Circular Geometry: A Buttress-Free Arrangement and Balanced Pressure Distribution

While in angular or oval pools the outward thrust of the water strains the straight walls, in the circular form the load distribution is naturally more balanced:

  • Hoop Stress: In a circular pool, hydrostatic pressure turns into circumferential tensile stress along the perimeter and stress concentration is reduced. For this reason, side support buttresses or retaining columns are not needed in circular models.
  • Above-Ground Installation Possibility: Because the circular frame closes on itself, it can be seated on suitably prepared level ground or on a platform whose load-bearing capacity has been verified. The bearing capacity and the flatness of the ground must be checked in every installation.
  • Reduction of Dead Flow Points: As there are no corners, the water leaving the nozzle creates a rotating flow within the pool; sediment is carried more effectively toward the central floor drain or the surface skimmer. Even so, floor vacuuming and periodic cleaning are necessary.
  • Volume / Perimeter Ratio: The circle is the geometry that gives the largest surface area for a given perimeter length; this contributes to efficient use of perimeter material per unit of volume.

02. Bora Pool Installation Discipline and Vortex Hydraulics

Sermed Havuz installation teams commission the Bora model on site with the following steps:

  1. Ground Preparation (Gravel or Level Ground): A protective base felt is laid over properly screeded ground. Optionally, lean concrete or a compacted gravel bed is used; thickness and compaction criteria are determined according to ground conditions.
  2. Unrolling and Joining of the Steel Shell: The special alloy steel shell sheet is seated onto the circular base rails and its end points are locked with high-strength steel bolts.
  3. Laying of the Monoblock Liner: The factory-made circular liner is spread over the base, the upper coping locking profiles are fitted, and the liner is seated onto the shell with vacuum assistance, after which water filling begins. Depending on the project, the liner is selected as a 0.8 mm homogeneous or a 1.5 mm reinforced membrane.
  4. MyBox Compact Filtration: The MyBox filter cabinet placed beside the pool is connected to the skimmer and nozzle lines. The electrical connection must be made by authorized electrical technical personnel with residual current protection in accordance with local standards. The position of the filter valve (multiport valve) must be changed only after the pump has been stopped.

03. Bora Round Pool Diameter, Volume and Installation Types Table

The volumes are approximate circular volume calculations for the stated depths (at a panel height of 1.50 m, the net water depth is taken as approximately 1.40 m). The durations are example values expected under suitable site conditions and are not an undertaking.

Model and Diameter (Ø)DepthApproximate Water VolumeInstallation TypeExample Installation Time
Bora Ø3.00 m1.20 m / 1.50 m~8.5 m³ / ~10 m³Above Ground / RecessedApproximately 4 - 6 hours
Bora Ø4.50 m1.20 m / 1.50 m~18 m³ / ~22 m³Above Ground / Semi-Recessed / RecessedApproximately 6 - 8 hours
Bora Ø6.00 m1.50 m (Net 1.40 m)~40 m³Above Ground / RecessedApproximately 1 day
Bora Ø8.00 m1.50 m (Net 1.40 m)~70 m³Semi-Recessed / Fully RecessedApproximately 1 - 2 days
Bora Ø10.00 m1.50 m (Net 1.40 m)~110 m³Fully Recessed / TerracedApproximately 2 days

Conclusion: The Bora circular pool combines rapid installation with balanced hydraulic behavior. Thanks to the load distribution of the circular form, a buttress-free and, in most cases, excavation-free installation is possible.

Frequently asked questions

What is the nozzle and circular hydraulic principle that reduces the formation of dead spots in the Bora circular pool?

In the Bora pool, the supply nozzle is positioned at a tangential angle. The water discharged from the nozzle moves along the circular wall and creates a rotating flow within the pool; in a corner-free structure, this flow makes it easier for the water to be directed toward the skimmer and the floor drain. The circulation time and the filter capacity must be selected according to the pool volume.

Will an above-ground Bora pool be damaged if it freezes in winter?

The steel frame and the elastic liner have a degree of flexibility, and the flexible ice compensator floats placed in the pool help reduce the pressure that ice expansion transfers to the frame. That said, freedom from damage under freezing conditions cannot be guaranteed; winterizing operations such as lowering the water level, draining the pipework and protecting the pump and the filter must be carried out in accordance with the manufacturer's instructions.

Can a wooden terrace be built around a Bora pool?

Yes; wooden or composite deck terraces can be built around Bora pools installed above ground or semi-recessed. The load-bearing system of the terrace must be calculated structurally, taking into account the decking, the water, the user loads and live loads, and it must be seated on a separate support structure so that it does not transfer load to the pool wall.

Is the water depth safe for children?

Bora models are available with depth options of 1.20 m or 1.50 m. A shallower depth makes use easier for families with small children; however, no depth removes the risk of drowning. For safety, uninterrupted adult supervision, a self-latching physical barrier around the pool and swimming lessons are all needed together; covers cannot be used in place of a barrier or supervision. Water chemicals must be dosed only according to the product label and the measured water values, and chemicals must never be mixed with one another.

Frequently asked questions →
Sermed Havuz technical team

Source: Sermed Havuz technical materials

Request a consultation →

Your next summer starts here.

Share your location and a photo of your space. We’ll help you choose a pool and cover.