← BlogCare & troubleshooting

Langelier Saturation Index (LSI): The Chemical Formula for Striking a Balance Between -0.3 and +0.3

To maintain the LSI balance, the water's pH (7.2-7.6), alkalinity (80-120 ppm), calcium hardness (200-300 ppm) and temperature should be measured regularly; the necessary corrections should be made according to the doses on the product label, applying each chemical separately, with the aim of keeping the LSI between -0.3 and +0.3.

6 min
Langelier Saturation Index (LSI): The Chemical Formula for Striking a Balance Between -0.3 and +0.3
Sermed Havuz photo · illustrative
Sermed Havuz technical team

Pool models, construction conditions and care to help you plan your project.

In this guide 4
  1. 01The Saturation Chemistry of Water: Aggressive Corrosion vs. Scale Deposition
  2. 02The LSI Mathematical Formula: The Balancing Algorithm of 5 Core Factors
  3. 03LSI Value Ranges and Their Effect on Pool Equipment
  4. 04Frequently Asked Questions

Application note: Chemical doses, pH/chlorine targets, run times and maintenance intervals are determined according to the product label, the measured water values, the usage class and local requirements. Numerical examples alone are not application instructions. Chemicals must never be mixed with one another; each product must be applied separately and in accordance with its label. The filter valve position must only be changed while the pump is switched off; electrical work, pressurized equipment work and pool draining must be carried out by authorized persons in accordance with local standards.

A common misconception among villa owners and facility managers in pool maintenance is to assume that water clarity is purely a matter of pH and free chlorine readings. Yet even clear water with a pH of 7.4 can be chemically unbalanced. The measure used to assess whether pool water will deposit scale on surfaces or, because it is not saturated with calcium, will instead attack metals and concrete grout joints is the Langelier Saturation Index (LSI). When the LSI value is not balanced within the -0.3 to +0.3 range, the risk of corrosion in metal equipment, scaling in heater exchangers and cloudiness in the water increases. At Sermed Havuz we recommend managing water balance with a measurement-based LSI approach.

Water is a solvent; it can dissolve a mineral it is not saturated with out of the surfaces it touches, and when there is an excess it can form deposits in the filter sand and the pipework. Balance begins with measuring the water chemistry.

01. The Saturation Chemistry of Water: Aggressive Corrosion vs. Scale Deposition

When the calcium carbonate balance in pool water is disturbed, these two extremes are seen:

  • Negative LSI (< -0.3): Aggressive and Corrosive Water: The water is not saturated with calcium; it can dissolve cement-based mortar and grout joints, accelerate corrosion in metal fittings, contribute to wear in heat pump circuits and accelerate the ageing of the liner surface.
  • Positive LSI (> +0.3): Scale-Forming Water: The water is saturated with calcium and precipitates the excess. A rough white layer of scale can form on the pool walls, the filter sand can cake over time and the water can turn cloudy.
  • The Error of Looking Only at pH: Even if the pH is 7.4, the LSI can shift into negative territory when the water temperature falls or the calcium hardness decreases.

02. The LSI Mathematical Formula: The Balancing Algorithm of 5 Core Factors

The LSI is commonly calculated using the following approach:

LSI = pH + TF (Temperature Factor) + CF (Calcium Factor) + AF (Alkalinity Factor) - TDS Constant (12.1)

  1. pH Measurement: The water pH is generally kept in the 7.2-7.6 range (the variable with the most direct effect on the result).
  2. Temperature Factor (TF): As the water warms the LSI rises (the tendency to scale increases); as it cools the LSI falls (the tendency to corrode increases). For this reason, water can behave more aggressively during the cold season.
  3. Calcium Hardness (CF): The common target range is 200-300 ppm CaCO₃.
  4. Total Alkalinity (AF): This is the pH buffer; it is generally targeted in the 80-120 ppm band.
  5. Total Dissolved Solids (TDS): Because TDS is high in pools with a salt generator, the constant used in the calculation is corrected according to the TDS range (for example to a value such as 12.2); the coefficient given by the table or software being used should be taken as the basis.

03. LSI Value Ranges and Their Effect on Pool Equipment

The effects below indicate general tendencies; the actual outcome depends on the material, the temperature and the duration of exposure.

LSI Score RangeChemical State of the WaterEffect on the Pool Shell and LinerEffect on the Pipework and Heater
< -0.50Extremely Corrosive / AggressiveAccelerates ageing of the liner surface, dissolves cement-based grout jointsThe risk of corrosion in the heat pump exchanger and pump components increases markedly
-0.30 to -0.01Slightly CorrosiveTolerable lower limitSlight risk of corrosion in metals
0.00 (Perfect Balance)Balanced WaterThe most suitable condition for the liner and surfacesThe most suitable condition in terms of equipment service life
+0.01 to +0.30Slightly Scale-FormingTolerable upper limitA thin calcium film may form
> +0.50Extremely Scale-DepositingWhite staining and crust on the surfaceCaking in the filter sand, scale build-up in the pipes

Conclusion: Keeping the LSI balance between -0.3 and +0.3 means approaching pool water through measurement rather than guesswork. Digital analysis kits make monitoring this balance easier.

Frequently asked questions

When the LSI balance is disturbed, how can pool water be kept from becoming corrosive or scale-forming?

To maintain the LSI balance, the water's pH (7.2-7.6), alkalinity (80-120 ppm), calcium hardness (200-300 ppm) and temperature should be measured regularly; the necessary corrections should be made according to the doses on the product label, applying each chemical separately, with the aim of keeping the LSI between -0.3 and +0.3.

Why does pool water become more corrosive in winter?

As the temperature falls the temperature factor decreases and the LSI value shifts in the negative direction; for this reason, keeping alkalinity and calcium hardness in the upper part of the target band as the cold season approaches can reduce the risk of corrosion. The values to be applied must be determined according to the measurement results.

Is it essential to work through complex formulas to calculate LSI?

No; mobile applications that calculate LSI, or digital photometers, will compute the score once the measured values are entered and can offer a starting value for the recommended chemical quantity. That recommendation should still be verified against the pool volume, the product label and a repeat measurement.

Is the LSI balance different in saltwater pools?

In salt electrolysis pools the water typically contains salt at a level of several thousand ppm, so the TDS is higher and the constant used in the calculation changes; in addition, the pH can tend to rise, so pH control and measurement-based dosing help maintain the LSI balance.

Frequently asked questions →
Sermed Havuz technical team

Source: Sermed Havuz technical materials

Request a consultation →

Your next summer starts here.

Share your location and a photo of your space. We’ll help you choose a pool and cover.