Pool models, construction conditions and care to help you plan your project.
In this guide 4
Application note: Chemical doses, pH and chlorine targets, run times and maintenance intervals are determined by the product label, measured water values, the use classification and local requirements. The numerical examples in this text are planning assumptions and are not, on their own, application instructions. Chemicals must never be mixed with one another, and electrical work, pressurized equipment and pool draining must be carried out under expert supervision.
When pool water turns green, the most common first reflex is to pour a large quantity of algaecide into the pool. Hours later, seeing that the water has not cleared, the owner pours in another bottle and the surface becomes covered with a layer of foam. Yet the basic principle of pool operation is this: once algae has formed, algaecide chemicals alone are not sufficient to eliminate the existing algae mass. Algaecides are primarily auxiliary products that delay the germination of algae spores. The factors that actually oxidize existing algae are elevated free chlorine at the correct pH range and prolonged, uninterrupted filtration that strains the dead algae out of the system. At Sermed Pools, our approach to fighting algae is built on hydraulic filtration discipline rather than wasted chemicals.
Algae is not solved simply by increasing the variety of chemicals. It is neutralized by the oxidizing power of chlorine, captured in the filter bed and then discharged through backwashing.
01. The Algaecide Misconception: The Difference Between a Preventive Agent and a Killing Agent
The major mistakes made in the fight against algae are as follows:
- Mistaking Algaecide for Medicine: Algaecide (algistatic) products mainly suppress spore development; they should not be expected to clear a fully grown green algae colony on their own.
- Overdosing and Foaming: Algaecide poured in above the label dose while the pool is green lowers the surface tension of the water in some product types; noticeable foaming can appear as the water moves.
- Waiting Without Brushing: Algae clings to surfaces and forms a protective biofilm layer. Unless the walls are cleaned with a suitable brush and the algae is dispersed into the water, chlorine contact remains limited.
02. Green Algae and Yellow Mustard Algae Eradication Protocol: Chlorine Shock and Brushing
The general algae recovery sequence recommended by Sermed Pools (final values are determined by measurement and the product label):
- Step 1: Bring the pH Down to the Target Range: pH can rise while algae photosynthesizes. Based on the measurement result, pH reducer is added to bring the pH typically into the 7.2-7.4 range, because the disinfection efficiency of chlorine is higher in this range.
- Step 2: Brush the Walls and Floor: The entire floor and all corners are swept with a brush suited to the surface, suspending the algae in the water.
- Step 3: High-Dose Chlorine Shock: Free chlorine is raised for shock purposes according to the measured pool volume and the product label; one example planning assumption is the 10-15 ppm range. As the algae cells break down, the green color generally turns greyish or milky white.
- Step 4: Prolonged Uninterrupted Filtration and Flocculant: The dead algae is drawn into the filter; a clarifier or flocculant is used if necessary, and backwashing is performed as the pressure gauge reading rises. The filter valve position is only changed while the pump is switched off.
03. Algae Prevention Methods: Effectiveness and Cost Table
| Method and Intervention | Algae Killing Power | Cost and Consumption | Effect on Pool Water |
|---|---|---|---|
| Pouring in Algaecide Only | Very low (does not clear existing algae, only delays it) | Risk of unnecessary chemical consumption | May cause foaming, does not remove the green color |
| Correct pH (7.2-7.4) + Shock Chlorination | High (the primary effective method) | Generally the economical main solution | At the appropriate dose, oxidizes algae in a short time |
| Uninterrupted Filtration (suitable filter media) | Captures and Discharges Dead Algae | Helps reduce the need for chemicals | Clarifies the water when run long enough |
| Weekly Preventive Algaecide Dose | Preventive (helps prevent spore formation) | Low, at the label dose | With regular use, delays the onset of algae |
Conclusion: What decides the fight against algae is not expensive chemicals, but correct pH, sufficient chlorine shock and uninterrupted operation of your filter.
Frequently asked questions
Can algaecide chemicals stop algae formation on their own, or is filtration the fundamental requirement?
Algaecide chemicals alone are not a reliable solution. The fundamental requirements are keeping the water's pH within the appropriate range based on measurement (typically 7.2-7.4), never letting free chlorine fall below the minimum level appropriate for the use classification, and running the filtration pump long enough to strain the pool volume through a sufficient number of turnovers per day. The daily run time is calculated from the volume, the pump flow rate and the intensity of use.
Why does the water turn milky white after the algae dies?
Algae cells broken down by chlorine lose their green color and turn into very fine greyish-white particles. At this stage, a flocculant or clarifier is added if necessary and the filtration time is extended to clear the water.
When should algaecide be added to the pool?
Algaecide is added as a preventive dose before the water turns green, preferably after a backwash. In a pool that has already gone green, the priority is not a preventive agent but pH correction and chlorine shock.
How does monoblock liner lining help prevent algae formation?
In ceramic and grouted finishes, the grout joints are areas where biofilm can take hold and remain protected. Depending on the use classification, a 0.8 mm homogeneous or 1.5 mm reinforced liner membrane is joined on site to create a continuous, smooth surface; because there are no grout joints, surface cleaning becomes easier and the effect of the disinfectant is more uniform. This is an advantage that makes maintenance easier; it does not replace regular filtration and monitoring of the water chemistry.

Fiplus ↗
Maldiv ↗
Bora ↗

