Pool models, construction conditions and care to help you plan your project.
In this guide 4
Calculation note: The prices, savings rates, energy consumption figures, rental income and payback periods on this page are explicitly assumption-based example calculations; they are not current Georgian prices, verified operating results or an income guarantee. A real budget must be calculated using local quotations, current tariffs, actual usage and a written scope of work. Timelines depend on site preparation, weather, permits and logistics.
One of the biggest question marks in the mind of a villa owner planning to build a pool is this: "Once the pool is built, will the monthly electricity and chemical costs upset my budget?" Hearsay often paints the pool as an energy monster. In reality, a pool's monthly operating cost is no surprise at all; it is a calculable equation based on the pump's motor power, daily running hours, the electricity tariff and the chemical demand of the water surface. At Sermed Pools, the inverter variable-speed pumps and smooth-surfaced liner finish we use in MyBox units (either the 0.80 mm homogeneous or the 1.50 mm reinforced option, with the type determined within the project scope) can noticeably reduce monthly operating costs compared with classic fixed-speed installations, provided the speed and filtration settings are configured appropriately. The actual difference varies with the selected equipment, water volume, intensity of use and the local electricity tariff.
The monthly operating cost of a 4x8 m villa pool (approximately 45 m3) consists of two main items: 1) the electricity consumption of a 0.75-1.0 HP pump running 8 hours a day (under these assumptions, an example range of roughly 130-220 kWh per month) and 2) the consumption of pH adjusters, disinfectant and algaecide. In systems using an inverter variable-speed pump and a salt chlorination generator, a strategy of long filtration cycles at low speed can be expected to deliver a significant reduction in electricity consumption and in the amount of chlorine purchased. The percentages here are not measured site results but example assumptions for planning purposes; precise values must be calculated from the pump curve, pipework losses and the usage profile.
When the right technology is selected, a pool's monthly electricity cost can remain on a scale comparable to the consumption of large domestic appliances. That comparison again depends on the system installed and the operating hours.
01. The 2 Core Monthly Costs of a Pool: Electricity Consumption and Chemical Use
The two main elements that make up a pool's monthly cost balance:
- 1. Electricity Cost: This is the cost of the kWh consumed according to the circulation pump's motor power. Example calculation: a 0.75 HP motor (assuming roughly 550 W drawn from the mains) running 8 hours a day consumes about 4.4 kWh per day and about 132 kWh per month. The actual power drawn varies with motor efficiency and the operating point.
- 2. Chemical Cost: This is the cost of the pH reducer (e.g. sodium bisulfate), disinfectant (tablet or liquid chlorine), algaecide and flocculant consumed to keep the water clear. Doses are always determined according to the product label and measured water values. On grouted and porous surfaces, biofilm cleaning can be more labour and chemical intensive, whereas smooth liner surfaces are generally easier to clean; the difference depends on water balance and maintenance discipline. Chemicals must never be mixed with one another under any circumstances; they should be added to the water separately and in diluted form.
02. The Pump Electricity Bill Formula and the Inverter Savings Mechanism
Electricity consumption is calculated with the following formula:
Monthly Electricity Cost = [Motor Power (kW) x Daily Running Hours x 30 Days] x Electricity Unit Tariff (Cost per kWh)
- How an Inverter Pump Works: Fixed-speed motors generally run at a single high speed, whereas a variable-speed pump can filter for long periods at a lower speed (e.g. around 1,400 RPM). Because of pump affinity relationships, the power drawn falls far more steeply than the speed; a pump running at low speed can therefore draw only a small fraction of its full-speed consumption. Since more time is needed to turn over the same water volume, the net gain must be worked out by considering speed and duration together. The wattage figures above are illustrative; the governing data is the power curve of the pump selected.
- Reduced Chlorine Purchasing Costs with Salt Chlorination: Because disinfectant is produced by electrolysis from refined salt added to the pool water, the need to buy packaged chlorine is greatly reduced. On the other hand, pH adjusters, occasional shock dosing and salt top-ups may still be required, so chemical costs do not disappear entirely.
03. Standard Pool vs. Sermed Smart Pool Monthly Consumption Table
The values below are not measured operating results but example planning figures based on the assumptions above.
| Consumption Item (4x8 m Pool) | Standard Pool with Fixed-Speed Pump | Sermed Inverter & Salt System | Example Monthly Difference Assumption |
|---|---|---|---|
| Pump Electricity (kWh/Month) | ~180 - 220 kWh / month (example) | ~60 - 100 kWh / month (example) | Noticeable reduction with long low-speed filtration |
| Chlorine Purchasing Cost | Continuous chlorine tablets and shock chlorine | Greatly reduced (produced from salt; salt and pH chemical costs continue) | Significant drop in packaged chlorine purchases |
| Algaecide and Flocculant | More intensive maintenance on grouted and rough surfaces | Dosing according to the label and water analysis (liner surface) | Reduction depends on maintenance discipline |
| Water Replacement Cost | Longer backwashes with a sand filter | Backwash water may be reduced with glass filter media | Depends on filter type and dirt load |
Conclusion: Smart equipment selection makes pool operating costs predictable. When correctly sized, an inverter pump and a salt generator help lower the monthly operating cost compared with classic fixed-speed installations.
Frequently asked questions
How much chemical does a 45 m3 pool need per month?
No single fixed figure can be given; the requirement varies with water temperature, the number of swimmers, sun exposure and the measured pH and free chlorine values. As an example summer-month assumption, a planning figure of 4-6 kg of disinfectant, 3-5 kg of pH reducer and a certain quantity of algaecide can be used. In pools with a salt generator, the need for packaged chlorine is greatly reduced, but the cost of pH adjusters and salt top-ups continues. Doses are always determined according to the product label and measurement results; chemicals are never mixed.
Does running the pump at night lower the electricity bill?
On a supply contract with a multi-rate (day/peak/night) tariff, running the pump during cheap tariff hours can reduce the bill. The size of the gain depends on the contract type and the tariff difference in force, so your meter type and tariff should be confirmed first. Whether filtration can be stopped entirely during the day must also be assessed separately in terms of water quality.
Is the cost of pool water evaporation high?
The rate of evaporation varies with air temperature, humidity, wind and water temperature; on hot, windy days, a water loss of a few millimetres per day is a typical planning assumption. Thermal covers over the surface can noticeably reduce evaporation; the extent of the reduction depends on the type of cover and how long it stays closed. A cover is not a substitute for a physical barrier and supervision.
How much does a pool cost per month in winter?
In a winterized pool, the pump is generally run only for very short periods or not at all, so electricity costs fall markedly. Even so, the water must still be monitored for freezing, contamination and biological growth, with winterizing chemicals and periodic checks applied as needed; costs therefore fall but may not drop to zero entirely.

Fiplus ↗
Maldiv ↗
Bora ↗

