Pool models, construction conditions and care to help you plan your project.
In this guide 4
Selection note: The Fiplus shell is a 20 mm F-Stone fiber cement panel; the galvanized steel external cross leg is a component separate from the shell. Maldiv and Bora have special alloy steel casings. Shell warranty periods are 25 years for Fiplus and 10 years for Maldiv/Bora; the scope and the exclusions depend on the written document. Dimensional, performance and certification compliance must be verified for the selected product and project. The volumes, loads and equipment quantities below are example planning assumptions; binding values are established by the structural design.
The large pools measuring 5x10 metres or 4x10 metres that are preferred in detached villas with large gardens or in boutique hotels reach a considerable hydrostatic load with the tens of tonnes of water they hold. Taking 5x10 m and an average water depth of 1.45 m as an example, the volume is roughly 72 m3 and the weight of water roughly 72 tonnes. Once the long side reaches 10 metres, the outward thrust of the water produces the highest bending moment at the midpoint of the wall span. Inadequately supported wall elements can deflect outwards under this load. Sermed Pools' Fiplus 20 mm F-Stone panels and the galvanized steel external cross leg / brace system, which is a component separate from them, are designed to carry this load across 10 metre spans as well; the brace spacing, the anchor detail and the base concrete must be verified by structural calculation for each project.
Building a large pool is a matter of structural calculation. Carrying a body of water that extends uninterrupted for 10 metres requires every single panel to be correctly keyed into the base concrete.
01. Hydrostatic Moment and Bulging Risk on 10 Meter Straight Walls
The main difficulties encountered in large scale pools such as 5x10 m are as follows:
- Maximum Bending Moment: The middle section of a 10 metre long wall is exposed to the highest bending effect because it is far from the corners that provide rigidity. Unsupported panels can deflect outwards.
- Mass Sloshing During an Earthquake: During an earthquake, the oscillation (sloshing) of a large body of water along a 10 metre line transfers dynamic loads to the walls. Seismic behaviour cannot be deduced from the shell material; dynamic water loads and ground conditions must be calculated by a qualified engineer in accordance with the local seismic code, and no commitment should be made regarding resistance to a particular earthquake magnitude.
- Increased Risk of Ground Settlement: As the pool gets longer, the likelihood of the ground properties varying along the span increases; one end may sit on firm ground and the other on softer fill. For this reason a geotechnical investigation is even more important for long pools.
- Filtration Circulation Becomes More Difficult: Over a distance of 10 metres, drawing the water from a single point may be inadequate; a distribution of multiple nozzles and skimmers is needed so that dead zones do not form.
02. The Sermed Pools Modular Support Architecture: Steel Braces at 1 Meter Intervals
On 10 metre Fiplus projects, Sermed Pools typically applies the following measures:
- A Hot Dip Galvanized Steel Brace Approximately Every 100 cm: On the 10 metre long side, 10 adjustable triangular steel braces are planned as a reference. In the reference detail, each brace is anchored into the 20 cm C30 base concrete with steel anchors and transfers the water thrust to the base slab. This spacing and the number of anchors are a reference detail; they can change according to the ground and the structural design.
- Vertical Stiffeners on the F-Stone Panels: The vertical reinforcing elements behind the panel limit flexing of the panel within its own plane, producing a more rigid wall surface.
- Upper Locking Belt and Coping Profile: The aluminium locking belt that runs along the top level of the panels ties the 10 metre line together like a beam and reduces lateral deflection.
- Twin Skimmers and 4 Adjustable Nozzles: For homogeneous filtration of the large body of water, twin skimmers are placed on the 10 metre line with 4 delivery nozzles opposite them, reducing the formation of dead zones. The final hydraulic layout is designed according to the selected flow rate.
03. Water Volume, Lateral Pressure and Structural Reinforcement Table for Large Pools
The values below are example planning figures calculated on the assumption of an average water depth of roughly 1.40-1.45 m. The lateral load column shows the approximate order of magnitude of the hydrostatic resultant acting on the wall and is not a binding structural result.
| Pool Size | Water Volume and Weight | Lateral Load on the 10 m Wall | Total Number of Braces | Recommended Filtration Capacity |
|---|---|---|---|---|
| Fiplus 4.00 x 8.00 m | ~45 m3 (45,000 kg) | resultant thrust in the order of ~30 tonnes (example) | 22 steel braces (reference) | 14 - 16 m3/hour pump |
| Fiplus 4.00 x 10.00 m | ~56 m3 (56,000 kg) | resultant thrust in the order of ~40 tonnes (example) | 26 steel braces (reference) | 18 - 22 m3/hour pump |
| Fiplus 5.00 x 10.00 m | ~72 m3 (72,000 kg) | resultant thrust in the order of ~50 tonnes (example) | 28 steel braces (reference) | 22 - 26 m3/hour pump (MyBox) |
| Fiplus 6.00 x 12.00 m | ~105 m3 (105,000 kg) | resultant thrust in the order of ~80 tonnes (example) | 34 steel braces (reference) | Commercial filtration with twin pumps |
Conclusion: The safety of a 10 metre pool depends on the braces and anchors along the long side being calculated correctly. The Fiplus modular panel architecture is designed to carry large water loads; actual behaviour depends on the structural design, correct installation and maintenance conditions.
Frequently asked questions
How are panel steel strength and pressure distribution achieved in large 10 metre villa pools?
Hot dip galvanized triangular steel braces placed approximately every 1 metre along the long sides transfer the water pressure to the base concrete; in the reference detail this is a 20 cm C30 base slab. The vertical stiffeners behind the panels and the upper locking belt help limit outward deflection of the wall. The brace spacing and the anchor and concrete detail must be verified against the project documents.
Is a single filter and pump enough for a 10 metre pool?
By way of an example calculation, a pool with a volume of 70 m3 needs a flow rate of roughly 70 / 4 = 18 m3/hour for the water to turn over once every 4 hours; a pump in the 18-22 m3/hour class and a filter tank of a matching cross section (approximately diameter 750-800 mm) are therefore planned. Whether the MyBox XL cabinet meets this capacity must be verified against the product data for the selected model.
Do the panels flex while a large pool is being filled with water?
When the simultaneous filling rule is applied, the crushed stone backfill outside is raised to a similar level as the water goes in; because the internal and external pressures are balanced, the expected deflection in the panels remains very small. Even so, plumb and level checks must be carried out during filling, and if any deviation is seen, filling should be stopped and the cause investigated.
How is the winter cover tensioned on a 10 metre pool?
On pools with wide spans, transverse safety straps and spring tensioning mechanisms are used so that the cover does not sag in the middle; porous mesh fabric reduces the pooling of water on top. A cover is no substitute for a physical barrier or for supervision; a perimeter barrier and continuous supervision are required where children are concerned.

Fiplus ↗
Maldiv ↗
Bora ↗

